- #CAN A COAX GPS ANTENNA BE CONNECTED TO A NMEA 2000 NETWORK SOFTWARE#
- #CAN A COAX GPS ANTENNA BE CONNECTED TO A NMEA 2000 NETWORK SERIES#
Always wear safety goggles, ear protection, and a dust mask when drilling, cutting, or sanding. These items are available at most marine dealers. You need the appropriate fasteners, tools, and mounts listed in each section.
#CAN A COAX GPS ANTENNA BE CONNECTED TO A NMEA 2000 NETWORK SERIES#
Icom makes rugged products that have been tested to and passed the following MIL-STD requirements and strict environmental standards.Īlso meets equicalent MIL-STD-810-C, -D, -E and -F.Īpplicable IP Rating and environmental test.® GPSMAP 4000/5000 SerieS i nSt AllA tion i nStructionS The GPSMAP 4000/5000 series chartplotter and GPS 17 antenna must be properly installed according to the following instructions. m cable connection to IC-M506GE, Microphone Bracket and Connector Mounting Kit / OPC-1541 6m Landing Cable for COMMANDMIC ™ HM-195B two extension cables to the basic cable can be combined to a total length of 18.3m / MB-132 Mounting bracket, for recessed mounting of the IC-M506GE in an instrument panel Handheld microphone / Mounting accessories (bracket) for mounting on / underneath / DC cable / Microphone suspension / GPS antennaģ56/5000 COMMANDMIC ™ HM-195B Remote Control Microphone incl. In addition, both components can be used as an intercom. It can be controlled remotely from the control station – all functions can be controlled from the COMMANDMIC ™, including the AIS reception functions. With an optional COMMANDMIC ™ HM-195B you can use the IC-M506GE z. Optional second intercom station possible The IC-M506GE and supplied HM-205B microphone can withstand 1m (3.2ft) depth of water for 60 minutes. *In accordance with applicable regulations, changes may only be made by the manufacturer or authorized dealer. This is also possible, if necessary, with the ATIS identifier assigned to inland navigation. The programming of the IC-M506GE with the individually assigned MMSI number for the DSC functions can be done by the user once * himself. Up to 100 DSC address IDs can be programmed. DSC functions include: distress, individual, group, all ships, urgency, safety, position request/report, polling request and DSC test calls.
70 (DSC channel) activity, even while you are receiving another channel. The built-in DSC watch function monitors Ch. The built-in 25 W amplifier increases your talk power, making it loud and clear.įour horn patterns are selectable for the automatic horn function when it is connected to the optional SP-37 horn speaker. The RX hailer function allows you to monitor the received audio from the horn speaker. When connected to the optional horn speaker, SP-37, you can talk with crews on the deck or shore from the radio’s microphone and can hear any reply via the horn speaker.
#CAN A COAX GPS ANTENNA BE CONNECTED TO A NMEA 2000 NETWORK SOFTWARE#
The bottom line of the dot-matrix display shows the software key functions which can be toggled with the left and right buttons. The intuitive software key functions provide easy and fast operation to control the multiple functions of the IC-M506GE. The function OFF setting is also possible. It reduces background noise to up to 90% in the received signal and 30% fixed in the transmitting signal. Using digital signal processing technology, the built-in bidirectional active noise cancelling provides superb performance. You can replay the received call, and not miss any incoming call. The last call voice recording function automatically saves the last two minutes of the last incoming call.
Using this function, the IC-M506GE can convert NMEA 0183 GPS data to NMEA 2000 data for other equipment.ĪIS information can only be passed to other devices (such as plotters) through the NMEA-2000 ™ connector. The M506GE can receive and transmit GPS (position, course (COG) and speed (SOG)), AIS report and DSC call information data and transmit radio frequency and PGN list data on the network. With the plug-and-play functionality of NMEA 2000, the IC-M506GE can easily connect to a NMEA 2000 network. The acquired position information can be used for DSC calls. AIS plotter displayĪ built-in GPS receiver with external antenna provides your location, bearing and speed by using information from GPS and GLONASS. The Plotter, Target list and Danger list can be toggled on the display. The AIS target call function allows you to easily set up a DSC individual call.
With an integrated AIS receiver, the IC-M506GE can show real-time AIS vessel traffic information on the display. Sometimes it is reassuring to know what you could do! Many possibilities that are not imposed on the user, but always offer a clear and simple operation.
0 kommentar(er)
